• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar

A Blog to Home

A Perfect Home Blog.

  • Home
  • House Cleaning
  • Home Decoration
  • Home Remedies
  • Product Reviews
Home » Home Remedies » Page 2

How to Clean a Burnt Pan with Coke

May 24, 2020 By Margie Rawls

How to Clean a Burnt Pan with Coke

Do you know the pain of a burnt frying pan? As you start to scrub out the next pot, you register the fact that you have burnt the thing to a crisp. Various effective home remedies can help you to remove stubborn burnt pan marks. What if I tell you there is a cost-effective and useful home remedy to clean a burnt pan? Yes, you can easily clean a burnt pan with Coke. Do you want to know how to clean a burnt pan with Coke at home? Let’s take a look at this effective home remedy to clean your burnt pan with Coke.

Causes of Burnt Marks And Scorched Pan

Following are the three top causes of the burnt pan:

  • The first reason for burning pan is that the pan is of low-quality material that does not heat as evenly, and the pans burn quickly as a result.
  • Second, the pans are without nonstick coatings due to which food gets stuck to the pan quite quickly.
  • Third, if you do not wipe your pan before each use and if the attached Grimes come in direct contact with stove burner, then they could end up burning onto the outside of the pan.

Well, you do not need to fret! You can remove rubber gloves and give rest to exhausted arms. You can use items that you already have in your kitchen to help loosen the mess. One of the things you can use is Coca-Cola. Yes, Coke contains acid that can remove the scorch marks without further harm the cookware. It is a solution that is easy, chemical-free, reduces your scrubbing time in half, and lets you keep your pan. Hurray!

How to Clean a Burnt Pan with Coke

You will need:

  • Coca-Cola
  • Plastic scrubber
  • Plastic or wooden scraper

Follow the following steps to clean a burnt pan with Coke.

Fill the pan with Coca-Cola.

Take your burnt pan, and add a sufficient amount of Coke to cover all of the scorched areas. Now add two to three inches of additional Coke to the pan as some evaporate in the heating process.

Make sure to dry off the bottom of the pan after filling it with Coke. You do not need to put it on the stove if there are drops of Coke that may fall onto the stove.

Bring to a boil

After filling the burnt pan with Coke, place it on the stove. Turn the heat up to high, and bring it to boil. Allow it to set in the pan for a few hours, or until the food is loosened.

Make sure to boil it, not just simmer it. You will know that it is boiling when you see large bubbles rising from the bottom of the pan, and it is giving off nearly continuous steam.

Scrape it

Use a scraper to remove as much of the residue as possible. You can use a plastic or wooden scraper. It would be easy to scrape it since the heat loosened the burnt food, and the Coke is acidic in nature. Therefore, it will not be hard to scrape it off.

Cool and scrub the pan.

After y have boiled the contents of the pan, remove it from the heat. Allow it to cool completely for half an hour. Discard the content– you will likely notice that the pan already looks a little cleaner. Next, scrub it to remove the burnt film and debris.

You may need to use a type of scrubbing tool to remove all of the scorch marks. Steel wool pads are efficient, but they often scratch the bottom of the pan, which may cause further harm. Sponges covered with plastic netting are an ideal substitute because they help scrub away scorch marks without scratching your pan.

This is how you can use Coke to clean the burnt food in your pan or pots. However, Coke is not the only way to clean the burnt food off your pans. Lemons, salts, baking soda, vinegar, water are few of the methods to remove the burnt marks. Take a look at how to clean a burnt pan with salt and how to clean a burnt pan with a dryer sheet.

The Stubborn Stain Removing Remedy for Burnt Pan

If there are super stubborn marks that don’t come off with scouring, try a paste of baking soda with a couple of drops of water. Now leave the paste on the marks for a while and return to clean as usual.

Tips

  • Before trying any cleaning method on a scorched pan, it is a wise idea to soak it in hot water to loosen up the debris. Let the water sit in the pan for at least half an hour (overnight is best).
  • The baking soda, vinegar, and oven cleaner methods are decent for stainless steel pans, but not for anodized aluminum or Teflon-coated cookware.
  • You should only handwash an anodized aluminum pan with hot water and dish soap.
  • Try cleaning a scorched Teflon pan in the dishwasher, which is safe for that type of cookware.

How to Prevent Pan from Burning

You can prevent the pan from burning in several ways.

  • Use high-quality pans that are made of high-quality material.
  • Search for the pan having nonstick coatings to avoid food sticking.
  • Pour enough oil into the pan first before start cooking as this provides a sort of nonstick coating.
  • Constantly stirring of food is essential as if the food sits in one spot too long, the side that faces the metal is more likely to burn and thus leave a burnt residue.
  • Also, rotate your pan while cooking so that food does not sit in one spot too long.

I hope now you can easily understand how to clean a burnt pan with Coke and remove stubborn marks from it.

How to Clean Electric Scooter

May 22, 2020 By Margie Rawls

How to Clean Electric ScooterIn today’s modern world, electric scooters have been one of the most convenient ways of commuting around the town. Whether you want to use it for office, college or fun, electric scooters are the best vehicles on the market. Not only they are fast but they are environment-friendly, money-saving and above all, hassle-free. From Fastest Electric scooter to 3 wheels Electric scooter, there is a variety of products available on the market. The regular usage on both roads and off-road adds dirt and other particles to the scooters. For best performance, it is important to maintain and clean electric scooter. Take a look at how to clean electric scooter easily.

Dust-Off the Scooter

Before you wash the electric scooter, dust off the scooter first. Use a dusting cloth or a rag for this purpose. It helps to remove the extra dirt or grime and also aids inspecting the bike to see if there is any damage or scratch on the bike.

Plug the Carburetor

The carburetor is an essential aspect of the scooter. In the case of the malfunctions, your scooter cannot work properly. Plug-in the carburetor to keep the water from entering into it.

Make a Water and Soap Solution to Clean the Body

The homemade cleaning solution is effective and money savers. Create a soap and water solution by adding soap to the bucker of water. Don’t use powerful soap for the cleaning solution because it may damage the paint of the electric scooter. Mix one cup of soap in a bucket of water.

Wash the Scooter with a Brush

Always use a soft brush to scrub the scooter because a brush with hard bristle may scratch the scooter paint. In order to prevent paint from burning, never leave the soap on the body for a long time. Also, it may leave some ugly stains on your scooter.

Decrease the Engine

In most cases, the electric scooter engine can be dusty or greasy. These conditions contribute to the malfunction of your scooter. It is significant to clean such parts to keep your scooter in the best performing condition. You can also use some liquid or cleaning solutions to decrease the engine.

Clean the Carburetor

The carburetor is one of the most crucial components of an electric scooter. A dusty carburetor affects the performance of your scooter and makes it run really slow. Not only this but also it causes issues to the gas to be distributed properly and thus the electric scooter can’t run on a stable speed. Read the user manual available with the specific scooter and remove the carburetor with the specified tools.

Take the gums off and dip the carburetor into the carburetor deep solution for about 20 minutes. Before placing it, use an air compressor to dry the carburetor properly. Now attach the gums to the carburetor and then attach it into the electric scooter.

What to Do while Cleaning

  • Make sure to tighten the battery cover before cleaning.
  • Make sure that the soapy water solution doesn’t enter into the bearings and chain of the scooter.
  • Use an old toothbrush for cleaning those areas that are hard to read rather than throwing water to such spots.
  • Use to rinse off the dust.
  • The environment-friendly cleaner is recommended for cleaning electric scooters.
  • Prevent your eyes or injured area from the soapy solution and chemicals. 

What Not to Do While Cleaning?

  • Don’t spray pressurized water on electrical components such as charging port, switches, etc.
  • Never rub dust and dirt on the hard surface. Rub them off when you spray water on washable areas.
  • Don’t spray any other solution on the tires except water because wax and sprays make your tires dangerously slippery.
  • Don’t wax textured plastic panels as it may lose the genuine shiny look.
  • Avoid washing oil muck to prevent pollution.
  • Don’t use a pressure washer on those high setting areas.
  • Never clean the electric scooter when the motor is in hot condition.

How to Clean Machete at Home

May 17, 2020 By Margie Rawls

How to Clean Machete at HomeIf you are looking for how to clean machete at home then here are some useful tips and tricks. Each best machete needs maintenance so you can work fast and efficiently.

Keep the Blade Sharp

A dull knife is not liked by everyone. So how to sharpen a machete, you should roll the knife and forth it on any stone. You should forth motion on both sides until it sharpens. It’s a basic sharpening trick. However, there is some industrial stone sharpen with oil. These are recommended for those who want over-sharpening.

Keep the Blade Oiled

Take any oil whether its veggie oil or any oil. However, if you have a bolo machete, we recommend the veggie oil. Also, we suggest you spray enough amount of WD-40 on the machete. Besides, if your knife’s sheath is not tight then oil inside the sheath. After that polish it. Also, tension against the sheath can cause unwanted friction which damages your blade. When you oiled both blade and sheath, keep it 10 to 15 minutes. Then rub both of them with sandpaper and alike other material. After that polish it. Here are some tips:

  • You should not leave your knife in the sun or in the rain. It can damage the knife’s sheath.
  • Don’t use a dry cloth for cleaning. Always use the damp cloth to clean out the sheath.
  • Keep your blade oiled on a regular basis.
  • Using for a while, sharpen the blade

Rusty Machete Restoration

It is a common thing that the knife gets rusty. It’s not a dough. So to remove dust, it is needed to clean the knife free from bacteria. However, if you are using a knife to cut food, then especially clean it regularly.

  • Rusty knife should be cleaned first before sharpening.
  • You should use aluminum oxide paper to get free from rust.
  • When you have removed the rust, then apply oil to prevent further rust.

Keep the Hilt Dry

You should keep in mind that excess moisture can lead a knife to crack. That’s why you should keep the hilt dry, so the knife stays longer.

The Conclusion

All in all, we have shared some useful guidelines on how to clean up a machete clean to enhance its lifespan. We hope you find these instructions useful. Thank you for visiting us!

How to Clean Rubber on Shoes

May 16, 2020 By Margie Rawls

How to Clean Rubber on Shoes

Dirt and grime buildup are two of the prime reasons for the discoloration of rubber on shoes. But you can clean rubber on shoes with some easy homemade cleaning hacks. You can make rubber soles look like new with a bit of effort. Here are some effective ways for how to clean rubber on shoes. You can also check how to remove tar from shoes to get rid of tar from shoes.

How to Clean Rubber on Shoes with Laundry Detergent and Baking Soda

First of all, remove the dirt and mud from your shoes. Take them outside and slap them together to eliminate the dirt or mud particles. Leaving too much mud on the shoes will take more time to clean them. You can use a key of a butter knife to remove set mud out of grooves in the shoe.

Now take a dry brush and scrape off the remaining loose dirt. It is a wise idea to eliminate maximum dirt from your shoes as it will take less time to clean them after creating the cleaning solution. Use a dry brush such as toothbrush but don’t use steel bristle brushes as they can damage the rubber soles of the shoes.

Now take baking soda and laundry detergent. Mix one part of each in a small bowl. The baking soda acts as an abrasive to aid the soap removing dirt and grime.

  • Don’t use laundry detergents with bleach agents.

Apply the cleaning solution on the rubber part of the shoes with the brush and scrub it in. For best results, use a circular motion as it is most effective to remove dirt and grime.

  • Don’t use it on the fabric of the shoe as baking soda can be tough to thoroughly rinse off.
  • Instead, create a separate mixture of water and detergent to clean cloth portions of shoes.

After properly scrubbing the cleaning solution into the rubber soles of the shoes, take a sponge or clean cloth and soak it in clean water. Now rub it along the rubber to rinse it with each pass until all the solution has been removed.

  • Don’t leave the detergent mixture on the shoe as it can make them very slippery and dangerous.
  • Leaving a cleaning mixture on the rubber can make it discoloring.

Dry Shoes Completly

Now it’s time to dry the shoes. After rinsing the soap off of the shoes, take a clean towel to dry the rubber before wearing it. Drying it completely will give you a better sense of how well the cleaning solution did the job. Repeat the cleaning process if necessary.

  • Don’t leave the shoes well as it can cause a bad smell.
  • Don’t wear wet shoes as it can be dangerous. Dry them completely before using them.

How to Clean Rubber on Shoes by Soaking Rubber Soles on the Shoes

Take a pan that is large enough to fit the shoes in it. Fill it with water to submerge only the rubber soles. Lukewarm water can be the best option to clean rubber on shoes. After filling the pan with enough water, it is time to add some dish soap to it. Add one squirt of mild dish detergent and mix it thoroughly. Dish soap works best with water to break up stuck-on grime.

For white shoes cleaning, choose a little amount of bleach than dish soap. Soak the rubber in the cleaning solution for a few minutes. Leave it for some time so that cleaning solution can break up on grime and dust. Soak only the rubber part of the shoes.

If shoes are really dirty, make sure to soak them in water for 15-25 minutes. Remove the shoes from the solution and use the soapy water to remove any remaining of dirt and grime that are present on the shoe’s rubber. Don’t use bristle brush as it can damage the shoes.

  • If necessary, soak the shoes again in the cleaning solution.
  • Don’t forget to wear gloves for a bleach solution to avoid skin damage.

How to Clean Rubber on Shoe with Nail Polish Remover

Nail polish remover is one of the best solutions to remove discoloration and grime from rubber on shoes. Never use nail polish remover on the cloth parts of the shoes. You can use many things to apply nail polish remover to the rubber on shoes but cotton balls are ideal due to their size and shape.

  • Wear gloves when using the nail polish remover.
  • For dirty shoes, use more than one cotton ball.

Apply the nail polish remover on the cotton balls and begin by scrubbing away the scuff marks on the rubber shoes. Scrub away the significant scuff marks before cleaning the rubber on shoes. After removing significant scuffs and stains from the sole of the shoes, run the soaked cotton balls along the entirety of the sole. It is essential to clean the entire sole because if don’t clean it, some part may look discolored as compared to brighter whites.

Cleaning Tips

  • Don’t use cleaners or detergents with bleach in them unless you aim to clean white shoes.
  • Make sure to rinse the shoes well as they can be seriously slippery.
  • After cleaning your shoes, you can use nail polish remover to touch up scuffs as they appear.
  • You can repeat the cleaning procedure if necessary.

How to Clean a Waffle Maker

May 15, 2020 By Margie Rawls

How to Clean a Waffle Maker

A waffle maker is an important part of your breakfast. In fact, it’s an additional luxury to eat delicious fluffy waffles at home. But it is also essential to know how to clean a waffle maker easily. The waffle maker gets messy with usage and needs a proper cleaning procedure. There are various ways to clean different types of waffle makers. Let’s take a look at some of the best waffle maker cleaning ways.

Cleaning an Electric Waffle Maker with Non-Removable Plates

First of all, unplug the waffle iron and let it cool properly. Many modern electric waffle irons are available with nonstick plates. For proper cleaning, it is essential to clean them without immersing in water.

Take a paper towel and remove excess oil from the waffle iron. Most people don’t use oil in a nonstick waffle iron but if you did, there must be some puddles of grease. They can be removed with a dry paper towel. Fold the paper towel in the point to push it between the iron ridges.

Take a soft-bristled brush and remove the large crumbs. Often it happens that dried batter stuck in the ridges. Brush away the large pieces with the help of a soft-bristled kitchen brush. Such type of kitchen brush doesn’t damage the non-stick surface of a waffle maker.

There may be heavy batter dried to the waffle iron, it can be seriously annoying to lose and remove them. The best idea is to soften the batter up first. Take a clean rag or a dish towel and soak it with warm water. Before placing it on the waffle maker, ring it out to avoid dripping. Now place it on the waffle maker and close it. Give it a few minutes to sit properly. The heat and the moisture from the rag will loosen up the pesky crumbs.

Rubber kitchen utensils are ideal for cleaning a waffle iron. The rubber doesn’t scratch the surface and the thin and malleable structure helps to get in between the waffle iron rows. After softening the dried batter with the wet rag, use a rubber spatula to remove the remaining batter off.

The sponge can also be used to remove the loosened batter. But use the one specially made for nonstick surfaces. Take a damp cloth but make sure it’s not wet. Because you don’t want the water to get in the electrical parts of the waffle iron as it can damage your waffle maker next time you turn it on. Clean everything that looks dirty or has batter on it.

How to Clean a Waffle Iron with Removable Plates

Unplug the waffle iron and allow it to cool properly. Follow the manufactures instruction and remove the plate from the waffle maker.

Immerse the waffle maker plates in the warm water. You can do this in the sink but a shallow dish of warm water can be very useful. Remember never add soap to the water for such cleaning. Because nonstick plates surface can deteriorate by doing this.

Gently clean the iron plates with brush or sponge. Use sponge or brush that is specially made for non-stick surfaces. You don’t want to damage the plate while cleaning.

Use warm water to rinse the waffle gird plates. Water will remove the remaining crumbs. Turn the plates to a vertical position so that the warm water can easily run through the ridges and rinse the spots which are missed with rag, sponge or brush. The dishwasher can damage the non-stick surface of the waffle iron. This method can be useful to prevent damages.

Give proper time to waffle maker plates to dry. Place the plates on the drying deck or on a dishtowel on the counter. For quick drying, you can use a paper towel or dry cloth. Just make sure that the plates are completely dry before putting them back in the waffle maker.

Don’t forget to clean the outside of the waffle iron. You can use damage cloth to clean the exterior surface. Be careful that the water doesn’t enter into the electrical parts of the iron.

Useful Tips to Maintain Waffle Maker

  • Before cleaning the waffle maker, it is important to read the manufacturer instructions.
  • Don’t submerge the electric waffle maker in the water.
  • Never use metal or sharp tools to eliminate the cooked waffles or to remove the caked-on batter.
  • If you don’t have kitchen brush, use an old toothbrush for removing crumbs.
  • Don’t use spray-on cooking oil. Use a pastry brush instead to lightly paint the waffle grids with oil.
  • Non-stick waffle doesn’t need a coating of cooking spray.

Warnings

  • Avoid using harsh scouring pads, abrasive cleaning pads or steel wool on the waffle grids.
  • Never use knives or pointed objects to eliminate batter out of the waffle grids.
  • Don’t use wet dripping sponge or cloth to clean waffle maker because the water can damage the electrical parts of the waffle iron.
  • « Go to Previous Page
  • Go to page 1
  • Go to page 2
  • Go to page 3
  • Go to page 4
  • Interim pages omitted …
  • Go to page 7
  • Go to Next Page »

Recent Posts

  • Best Electric Smoker Under 200 in 2020
  • How to Clean Tile Floors with Vinegar and Baking Soda
  • How to Clean Oven Glass
  • How to Clean Burnt Pan with Dryer Sheet
  • How to Remove Old Stains from Carpet
  • How to Remove Rust Stains from Clothes with Vinegar
  • How to Clean Windows with Vinegar and Baking Soda
  • How to Clean Headlights with Household Items
  • How To Cleaning Toilet Tank- Easy Cleaning Hacks
  • How to Clean Bathroom with Vinegar
  • About Us
  • Contact Us
  • Privacy Policy
Copyright © 2020 A Blog to Home - All Right Reserved